Product Overview
Kapton tape is a thin polyimide film coated with a pressure-sensitive silicone adhesive. On the roll it is a general-purpose insulation and masking material; cut and shaped, it becomes a finished part that belongs to one exact place in your assembly — a shaped insulator under a board, a mask over a connector while the assembly passes through solder, a protective piece over a sensor or a terminal that runs hot. That conversion is the work we do at Huatech Vietnam.
We take the Kapton film grade your application calls for and cut it to your outline: rings, rectangles, dot arrays, narrow strips and small profiles with holes and slits, all with clean edges and the same shape from the first piece of the run to the last. Parts are normally supplied die-cut on a release liner, in roll form or flat, so your operator or your feeder peels and places a finished part instead of cutting tape on the line.
Buyers come to us at three points. Some are hand-cutting tape from a roll today and want a shape that repeats. Some are building a new board or module and have a drawing but no production route for it. Others are re-ordering a part that has drifted on dimensions with another converter and need the geometry held. In all three cases the deliverable is the same: polyimide components cut to the drawing, ready to place.
The parts go into electrical insulation, heat-resistant masking and component protection in electronics, electrical equipment, automotive electronics and general industrial assemblies. Because the same site also runs a printing label workshop, Huatech Vietnam works as an industrial label manufacturer as well, so safety warning labels and other printed identification for the same hot zone can be quoted with the tape parts instead of through a second supplier.
OEM/ODM development is available. Send a drawing, a sample, or a description of the gap the part has to cover, and our engineers will come back with a proposed film grade, adhesive, thickness and shape to approve.
Converting Processes & Precision
- Die cutting — the film and adhesive are cut through to the outline you specify, so the finished part lifts off the liner as a single shaped piece with clean edges; the same die-cutting route is used for printed high temperature labels.
- Kiss cutting — the tape face is cut and the release liner is left intact, which is how parts are supplied in roll form for peel-and-place feeding on a line.
- Laminating — an adhesive layer, a second liner or a carrier film can be added where the part has to bond in place, stay flat, or be handled by machine.
- Slitting — rolls are slit to the width your feeder or your operator needs, before or after shaping.
- Tool design and repeatability — the cutting tool is set to your drawing and kept for repeat orders, so the shape does not change between runs.
- Edge quality — the cut edge and the profile are checked as the run moves, because a burr or a ragged edge on a thin film can lift, tear or bridge where it should insulate.
- Different shapes need different handling — a large flat mask and a very small dot part take different liners, different web tension and different packing, and the process is set accordingly.
Material & Heat Performance
Kapton is a DuPont brand name for polyimide film, and the tape we convert is that film with a pressure-sensitive silicone adhesive on one side. The material is chosen for a combination few films offer at once: it keeps its shape and its electrical insulation through high temperatures, resists most solvents and cleaning agents, does not go brittle as it ages, and stays thin, so it can sit between two surfaces that are already close together.
What that means in practice is that the part keeps doing its job after the heat cycle, not only during it. A mask that has been through a soldering or curing pass still peels away; an insulating barrier that has been warm for months still holds its dielectric separation; a protective piece over a terminal does not curl at the edge and lift.
The limits matter as much as the performance. Polyimide tape is not a gap filler and not a cushioning foam — it is thin, so it covers a surface rather than filling a space, and it is not a structural adhesive. Working temperature is not a single figure: it depends on the film grade, the adhesive system and how long the part is exposed. Tell us the process temperature and the dwell time and we will match the tape to it rather than quote one number for every grade.
The same polyimide family also carries printed identification. Heat resistant labels for equipment surfaces and control panels close to hot zones are made from heat-stable film stock, printed, and die-cut on the same converting floor as your tape parts.
Specifications
| Material | Kapton (polyimide) film tape |
| Adhesive | Pressure-sensitive silicone adhesive, depending on the selected tape product |
| Film thickness | Matched to the tape grade and to the space the part has to fit into |
| Shape | Custom die-cut outlines, including holes, slits, rings, strips and dot arrays |
| Cutting methods | Die cutting, kiss cutting, laminating and slitting |
| Liner and handling | Parts left on the release liner, kiss-cut in roll form, or supplied flat |
| Temperature requirement | Matched to your process conditions — share the working temperature and the dwell time |
| Drawings accepted | Dimensioned drawings, PDF or CAD files, or a physical sample part |
| OEM/ODM | Available for new part development and repeat supply |
| Quality checks | Dimensions, cutting precision and shape consistency verified against your drawing |
| Customization inputs | Dimensions, thickness, shape, adhesive specification and temperature requirement |
Applications
- Circuit board protection — shaped pieces placed over pads, vias and components that must be shielded during a soldering, wave or reflow pass, then removed cleanly.
- Insulation inside electrical equipment — barriers and cover pieces in power supplies, transformers, motors and control panels where a thin, heat-stable dielectric is needed.
- Wire and terminal protection — small die-cut wraps and covers that keep conductors and terminals clear of a hot or conductive surface, with hazard warning label pieces for the same terminal printed on the same site.
- Automotive electronics — insulation and masking parts for sensors, connectors and control modules that see under-hood heat cycles.
- High-temperature masking in production — custom masks that keep plating, coating, adhesive or connector areas clear while a part passes through an oven, curing or coating line.
- Sensor and component protection — protective pieces over thermistors, battery contacts and small sensors during assembly and handling.
- General industrial equipment — insulation shims, surface protection and custom-shaped parts where the drawing, not a catalogue, decides the geometry.
Marking & Identification Options
- High temperature labels — polyimide and other heat-stable stock printed for boards, cables, fixtures and equipment that pass through ovens, reflow lines or burn-in, where ordinary paper or vinyl stock would lift, curl or darken.
- Heat resistant labels — for equipment surfaces, control panels and machine housings close to a hot zone, printed with the part number, rating or service information and die-cut to whatever shape the surface allows.
- Safety warning labels — operator-facing warnings for electrical equipment, machinery and enclosures, printed and die-cut in the same building as the tape parts, so wording, size and placement can be agreed with the engineering team that handles your insulation parts.
- Hazard warning label printing — die-cut warning pieces for live terminals, hot surfaces and moving parts, produced from the artwork your team supplies.
- Custom product label printing — the plant also runs wider printed identification work, so a programme can take insulation parts and printed parts from one supplier and one set of paperwork.
- Coordination — send the marking artwork with the tape drawing and both are quoted, sampled and scheduled together rather than as two separate purchases.
Cost Control & Production Flexibility
- Material yield — die layouts are nested so more parts come off each length of film, and on a thin-film part that layout is where most of the cost sits.
- Prototype-first development — a first run can be small, so a change to the outline or the adhesive costs a handful of parts instead of a full production batch.
- Re-orders without fresh setup — your cutting tool and setup are kept, so a repeat order does not start again from tooling.
- Printed parts from the same plant — heat resistant labels and custom product label printing run alongside the converting lines, so identification and insulation parts can be planned on one schedule instead of two.
- One supplier instead of several — insulation, film and printed parts are made in the same Bac Ninh plant, and the company’s work as an industrial label manufacturer sits under the same roof, so there is no second supplier’s setup, artwork or freight to absorb.
Packing & Supply Formats
Converted polyimide parts are supplied in the format your line can take. Small shaped parts are usually delivered die-cut on a release liner, wound on a cardboard core so an operator or a feeder can peel them one at a time; larger masks and covers are more often supplied as flat sheets or as loose custom-cut pieces in a stack. If your process uses a tape-and-reel feeder or a pick-and-place head, tell us the liner and the feed direction and the roll is wound and slit to suit it.
Packing is built around what the parts are. A thin film part can be deformed by pressure, contaminated by dust or curled by humidity, which is why parts stay on their liner, are interleaved or bagged where the shape calls for it, and are supported so a roll cannot crush in transit. Counting and identification are done as the parts are packed, so the carton matches the packing list that travels with it.
The packing format itself is agreed per order rather than fixed. Piece count per bag or per roll, liner type, core size and the outer carton or pallet are set against the part dimensions and the quantity you order, and any particular requirement your production line has — a liner for a feeder, parts counted as a set per assembly — is built into the packing instruction.
Drawing Review & Technical Support
- Send the part — a dimensioned drawing as PDF or CAD, a sketch with measurements, a physical sample, or the component the part has to fit.
- Explain what the part must do — insulate, mask, protect or keep a surface clear — because the function decides the film grade and the adhesive more than the outline does.
- Give the working conditions — the temperature the part sees, how long it is exposed, the chemicals or cleaning agents it meets, and whether it is removed after the process or left in place.
- Confirm how the adhesive has to behave — permanent hold, clean peel, or grip only until the assembly is closed.
- Flag identification requirements — if the same assembly carries high temperature labels, send that artwork with the drawing so both parts are quoted and scheduled together.
- Artwork for printed parts — where the programme also involves custom product label printing, the print file, material preference and finish travel with the same enquiry.
- Review and proposal — our engineers read the drawing against the application and come back with a suggested film grade, adhesive, thickness, shape and tooling route, so you approve a defined part rather than a sketch.
- Sample and approval — a sample or first-article part is produced for you to try on the line, and the approved part becomes the reference for the production run.
Ordering & Delivery
- Order quantity — set per part rather than as a fixed figure. Prototype and small-batch runs are supported, and repeat and volume orders are scheduled on the same tooling.
- Lead time — small buyers who order without a factory audit are typically served in about 5–15 days; larger accounts that require a factory audit usually run about 30–90 days from the start of the process.
- What to send with an enquiry — the drawing or sample, what the part has to do, the working temperature, your adhesive preference, the quantity you need and the date your line needs the parts.
- OEM/ODM — available: we build to your drawing and your part number, and we can develop a shape that does not exist yet.
- Printed parts on the same order — because Huatech Vietnam also works as an industrial label manufacturer, printed identification can be quoted alongside the converted tape parts.
- Warning marking — if the equipment also needs safety warning labels, include the artwork in the enquiry and both parts are produced in the same plant.
- Terms — pricing, freight and payment terms are confirmed with your sales contact when the order is placed.
- Contact — market@huatech-vietnam.com, or phone, Zalo and WhatsApp on +84 395 237 345.
Quality Control & Inspection
Quality is controlled at every stage at Huatech Vina, not only at the end. Our 12 in-house engineers agree the inspection points with you before production starts; first articles are checked and approved, and our QC team samples parts as the run moves through. Our quality system is certified to ISO 9001, ISO 14000 and IATF 16949, and we support the factory audits and third-party inspections larger customers arrange. Shipments leave with the inspection records your incoming team needs, and anything outside the agreed specification is held and reported before it goes out.
FAQ
Q1. What is cut and shaped Kapton tape used for?
It is polyimide tape converted into a finished part rather than left on the roll. Typical jobs are electrical insulation inside equipment, heat-resistant masking while a board or component passes through soldering, curing or coating, and protection over a component, terminal or sensor that has to survive heat and handling. The shape is what makes it useful: the part covers the exact area on your assembly, is placed by hand or by machine, and gives the same coverage on every unit instead of a hand-cut piece of roll tape.
Q2. Can you customize Kapton tape shapes and sizes?
Yes. We work to your drawing, so the outline, hole positions, slits, ring diameters and the layout on the sheet or roll are made to your dimensions rather than picked from a list. Small complex profiles, dot arrays and long narrow strips are all produced by die cutting, and the same tool is reused so repeat orders match the first delivery. If you only have a sample, or the component the part has to fit, send that instead of a drawing and we will work from it.
Q3. Can you process different Kapton tape thicknesses?
Thickness comes with the tape grade you select, so it depends on the tape product, the adhesive system and what the part has to do. Thin film suits tight spaces and low-profile coverage, while a heavier grade is easier to handle and position where the part is picked up and placed several times. Tell us the space available and the handling the part will see, and we will confirm which grade to cut.
Q4. How do you ensure product quality?
Every part is measured against the drawing you approved — the outline, hole positions, cut edges and shape consistency are checked as the run moves, not only at the end. Parts that fall outside the agreed dimensions are separated rather than packed. Because the same tool cuts the whole order, the shape does not drift between the first piece and the last, and if your own inspection finds something the drawing does not explain, the part comes back to us and the tool is re-checked.
Q5. Which adhesive is used on the converted parts?
The parts are made from pressure-sensitive silicone adhesive tape, and the exact adhesive system follows the Kapton tape product selected for the job. Silicone adhesive is the usual choice where the part has to hold in heat and then come away without leaving a heavy residue, but the right answer depends on the surface it sits on and whether the part is permanent or temporary. Tell us the surface and whether the part is removed after the process.
Q6. Can the parts be supplied on a release liner for automated placement?
Yes. Parts can be kiss-cut and left on the liner in roll form so they are peeled one at a time, or supplied as flat pieces on a sheet. If your line uses a feeder or a pick-and-place head, tell us the liner and the feed direction and the roll is wound and slit to match.
Q7. Do the parts hold up to soldering and reflow masking duty?
Polyimide tape is chosen precisely because it tolerates soldering, reflow and curing conditions better than ordinary film tapes, and shaped masks are widely used to keep solder, coating or adhesive off selected areas. How long a part can stay in the process depends on the film grade, the adhesive and the temperature profile, so share your profile and dwell time and we will confirm the grade that suits it.
Q8. Can you supply the printed identification that goes with these parts?
Yes. Die-cutting and printing sit in the same plant, so a programme can order converted tape parts and the marking that goes with them together. Polyimide and other heat-stable stock is used for identification that has to stay readable in a hot zone, including a hazard warning label applied beside a live terminal or a hot surface, and printed pieces are die-cut to the same drawing discipline as the tape parts.
Contact Huatech Vietnam
Looking for Kapton tape cutting and shaping services? Contact Huatech Vietnam for customized tape converting solutions.
- Facebook: Follow Huatech Vietnam
- Contact Us: Request a Quote
- Email: market@huatech-vietnam.com
- Phone/Zalo/WhatsApp: +84 395 237 345









Đánh giá
Chưa có đánh giá nào.